Thank you for purchasing our products and we will offer our best service to you sincerely.

For the safety, please read & understand this intstruction thoroughly before installation 

and operation.

Automatic Sensor Faucet

Instruction of Installation and Operation

Warnings   ………………………………………………………………………………………………………………………………………….
Specifications   ……………………………………………………………………………………………………………………………………
Before usage   …………………………………………………………………………………………………………………………………….

spare parts   …………………………………………………………………………………………………………………………

Confirmthe
Name of spare parts   …………………………………………………………………………………………………………………………….
Installation position of the faucet   …………………………………………………………………………………………………………….
Installation of control box  ………………………………………………………………………………………………………………………
Connection of spare parts  ……………………………………………………………………………………………………………………..
Installation or replacement of battery   ………………………………………………………………………………………………………
Testing and usage   ………………………………………………………………………………………………………………………………
Care and cleaning   ……………………………………………………………………………………………………………………………… 
Clean the filtration system   …………………………………………………………………………………………………………………….

eriodic maintenance   ………………………………………………………………………………………………………………………….

P
Long-term supension of use    ………………………………………………………………………………………………………………….

rouble   …………………………………………………………………………………………………………………………………..

Product t

   …………………………………………………………………………………………………………………………………

Trouble shooting

Warnings

Please DON’T disassemble, repair or refit the products, because it might lead to electricity shock 
or product breakdown, unless stated otherwise.

Please DON’T install the products in humid place, especially in bathroom or Sauna room.

Please DON’T strike the products, as this may damage the unit or cause water leakage.  

Please DON’T use the product in the place where freezing might be occurred.

Please ensure that the power line separates from hot water line/tube

Please keep the detecting scope clear to avoid interference.

Please install the power socket/outlet in the place where water cannot be reached or sprayed.

Specifications

Power

supply

           AC
AC   220~240V

DC 

4*1.5V AA Alkaline batteries

Sensor

detection

range                                     

Ambient

temperature

HumidMax.90RH

Water pressure

                Product consumption                                   

Flowrate                      

1

   1
   1
   2
   2
   3
   4
   5
   5
   6
   6
   7
   7
   8
   8
   8 
   9

For the safety and smooth operation, please pay attention on the following warnings.

Contents

Common Tools needed

Adjustable

wrench

Screwdriver(Phillips)

5~250mm 

（

base on 300*300mm white board

）

               1

~

55

℃

Humidity 

5

~

0

.

7MPa

                                 Standby: ≤2W；Active:≤5W

–

Before usage

1.Please read this instruction manual carefully and fix the products correctly.

2.We reserve the rights to upgrade products without a notice.

3.Flush the water supply pipes thoroughly to remove debris. Faucet is 

   designed for tap water or potable water.

4

.Please check whether the following spare parts completed or not.

Confirm

the

spare parts

Spout for faucet

Control box

Screw part

AC Adapter

 (AC)

Note

 :

As to the spare parts of power supply, please refer to the type of your purchased products.

2

Self-tapping Screw*5pcs

Anchor*5pcs

3

Sensor

Nozzle

Spout

Battery box

AC adapter

Sensor

plug

AC adapter input plug

Water inlet

Water outlet

Water outlet hose

Name of spare parts

Notes：

Fo

r the power adapter, please refer to the 

type  you purchased.

Control box

Power output plug

Valve plug

S.S bracket

4

1

2

0

°

1

2

0

°

5mm

Installation of water faucet (

I

nstalled on the fa

k

e wall)

①                                          ②                                        ③                             ④

P

repare the 

32mm PVC 
pipe by the 
user

I

nstall the 

decorative cover

A

djust the location 

of spout then fasten 
the nut

B

ring out the 

pipe and cable

F

ix the spout 

with

32mm

32mm

E

mbedded slot

P

repare the 

32mm PVC 
flange pipe 
by the user

175

1

1

5

8

2

0

72

Installation position of the faucet

Installation of water faucet (installed on the soild wall)

①                   ②                                              ③                     ④                         ⑤

44mm

I

nstall the pipe 

and cable

Please take your purchased product as final, the outlook shown in the diagram might be different from the actual product.

Tips

:

1. Please make sure there is enough space 
    for installation of control box of faucet.

2. The given dimensions shown on the diagram 
     is for reference only, the actual size might be 
    different than those indicated on the diagram.

Diagram

S

ingle-cold type

（     ）

（          ）

进

水

W

a

t

e

r i

n

c

o

m

i

n

g 

1

5

0

~

3

0

0

F

inish the installation!

1. Cut the wall then make slot and embed 32mm PVC pipe used for cable.

2. Mark the installation holes according to diagram ② then drill the holes.

3. Install the pipe and cable into the embedded PVC pipe and birng out them then  fix the spout with the equipped screw according to 

    the diagram ③.

4. Install the decorative cover and adjust its location then finish the installation.

I

nstall the pipe 

and cable

B

ring out the 

pipe and cable

F

inish the installation!

1. Mark the location of inlet and outlet of cable and pipe and cut the hole with 32mm diameter for cable and pipe according to 

    diagram ①.

2. Install the pipe and cable into the proposed hole and bring out them according to the diagram ②.

3. Adjust the location of spout and fix it onto the fa

k

e wall by the equipped screws.

4. Install the decorative cover and adjust its location then finish the installation.

110

5

3

8

2

0

R

e fe re nc ed fi n i s h e d 

h e i g h t 200 mm

68

R

e

f

e

r

e

n

c

e

d f

i

n

i

s

h

e

d

 h

e

i

g

h

t o

f c

o

u

n

t

e

r t

o

p

88

5

Spout

Battery box

AC adapter

Water inlet hose

AC adapter input plug

Water inlet

Water outlet

Water outlet hose

Power output plug

Valve plug

2

Installation of control box

1

9

m

m

Screw hole

Screw hole

I

nstallation of  control box

Drill 2 pcs 5mm holes on the proposed wall according to the dimension shown on the diagram ① and 
install the screws, then fix the control box onto the wall in accordance with diagram ② (fix the S.S bracket 
located on the back of the host on the pre-installed screws).

①                     ②                          ③

Completed diagram

Screw 

Hang the control box on 
the screw

S.S bracket

1. Connect the water incoming 

    pipe into the inlet of control 

    box according to the diagram 

    then fasten it by wrench.

2. Connect the water outgoing 

    pipe into the outlet of control 

    box according to the diagram 

    then tight it by wrench.

3. Connect the sensor cable of 

    water faucet into the 

valve plug 

    & power output plug

  of control 

    box according 

    to the marked direction.

4. Connect the AC adapter’s output 

    plug into the AC 

adapter 

input 

    plug of control box.

Note：
Please ensure the incoming and outgoing water pipe are connected closely and 
comprehensively  to avoid water leakage.

2

Connection of spare parts 

6

I

nner light 

of sensor

Sensor

把手伸到水龙头嘴下方。

P

ut your hands under 

the nozzle of faucet.

把手从水龙头嘴下方移走。

M

ove your hands away.

I

nner light 

of sensor

Sensor

P

ut your hands under 

the nozzle of faucet.

M

ove your hands away.

1. Water dispensing

Pu

t your hands under the faucet (50-120mm from the 

    nozzle) then the water will be dispensed automatically.

    No

te: 

P

lease 

do

not

 block the nozzle by hands to avoid 

    the water spraying).

2. Water stoppage

 Re

move your hands away then the water will be stopped 

    automatically.

Ti

ps: 

T

here is 

6

0 seconds setting in this device, it will stop 

dispensing water automatically with 30 seconds even the 
hands are still under the device.

Testing and commissioning 

After completion of installation, please test the product 
according to the following instructions:

Usage

Pease use the unit as below after the testing 
is done:

1. Connect the power:

    Connect the AC or DC power after the installation 
    of device.

2. Confirm the sensor:

①. Please confirm the sensor inner light is stop flashing 
     or not when there is no objects in front of sensor (after 
     connecting the power, the inner light will flash and set 
     the sensing distance automatically.

②. If the inner light is still flashing, please adjust the nozzle’s 
     direction slightly until the flash stop.

③. About 10 minutes passed after connecting the power, the 
     sensor will finish the flash and sensing distance setting. 
     If the direction of faucet nozzle is failed to set up after the 
     sensor stops the flash, then please disconnect the sensor 
     cable and repeat the above steps. 

Testing and using

Installation or replacement of battery

I

nstall 4 AA batteries

T

ake out 

battery case 

Open the 

battery

 cover 

of control box 

1. 

Open the battery cover of control 

    box and take out the battery case 

    according to the diagram ①.

2. 

install 4 pcs AA batteries correctly 

    and put the battery case into the 

    control box and fix its cover as per 

    diagram ②.

Note：

This product is sold without battery.

Note：
Please place the batteries correctly 
according to the anode and cathode. 

①          ②

7

Sensor

Care & Cleaning

For light cleaning

Please use the soft cloth soaked with water and drying it and 

then to wipe off the stain affixed on spout & sensor cabinet.

For heavy- dirt cleaning

Please use the cloth soaked with right amount of neutral detergent 

to wipe off the stain and then clean by water.

Please be careful during cleaning surrounding of sensor cabinet to 

avoid the scratching.

Please do not use the detergent which might do harm to the spout 

such as acid detergent, chlorine decolorizer & alkali detergent.

The following items are prohibited to adopt for cleaning the product.

The detergents contained abrasive grain, such as polishing powder. 

Solvent  such as 

：

 Paint and the solvent covered benzene.

Abrasive such as 

：

Nylon brush/steel wool,etc.

T

ake out the 

filter net

F

ilter net

Clean the filtration system

W

ash the fliter 

net by water

F

ilter net

The control box is equipped with independent 

filtration system, but if the water quality is low 

inside the pipe and with the long-term usage, 

the water dispensing might be not good, in this 

case, please follow below instructions.

1. Turn off the angle valve placed on the water 

    supply to avoid the water flow during the 

    cleaning.

2.

Unscrew the inlet pipe and take out the filter 

   net from water inlet of control box then wash 

   the blockage and finally fix the filter device

. 

8

 Periodic maintenance

Long-term suspension of use

Product trouble 

T

wice annually：

1. Please check all the connected parts to see whether there is leakage or not, and fasten 

    or change the loosen or wear-out spare parts according to the real situation.

2. Please check the faucet and control to see whether they are loosen or not and fasten 

    they if needed.

N

on

periodic

inspection

：

1. Please clean  the dirty when the sensing distance becomes short and the dirty is found 

    on the sensor shell or case.

2. If the water is coming out for 2 seconds and the light of sensor flashes quickly in 2 

    seconds, it shows the batteries are in insufficient, please change the batteries

  （For the DC type).

Please follow below instructions when the unit is in long-term suspension of use

1. Turn off the incoming valve or main valve of water faucet. 

2. Cut off the AC power and take out the batteries.

Please follow the below instructions in case product in trouble

1. Please check the Trouble Shooting table in case product in trouble to solve the problem.

2. Once there is water leakage occurred, please turn off the water valve then conduct the 

    trouble shooting.

3. If the trouble shooting is failed even all the given instructions had been tried, then 

    please contact the installer or the distributor. 

Some trouble symptoms can be identified by the indicator’s flashing. 

         Symptoms                                      Probable Causes

                                       Corrective Action

No battery or wrongly connected 
No power supply or wrong connection
Object in sensing range
Dirt on the sensing window
The connector does not connect well

No water flow while 

the indicator flashes

Keep water out within 1 minute 

while indicator does not flash 

Just finishing installation
The connector assemblies are closed
Aerator is blocked

The filter is blocked                                      Clean filter
The connector assemblies are not open 
completely
The filter is blocked
Aerator is dirty
The supply water pressure is lower

Turn counterclockwise the adjustment bolts on 
connector assemblies with  the hex wrench
Clean filter
Clean the aerator
Check the water supply system

  Wait for 10 minutes
  Open the connector assemblies
  Clean the aerato

Check the batteries
Check the power supply and the conncetion
Remove the object
Clean the sensing window
Check the connector

No water flow
(Indicator not flashing)

The indicator flashes once
every 2 seconds and the 

water  doesn’t flow out.

Low water flow while the 
indicator does not flash

Object in sensing range 

Remove object

Refer to “Note of the Indicator Flashing”

Please contact with distributor, if the trouble remains after above-mentioned actions are 

taken

. 

Please do not disassembly the other parts of the faucet freely except installing and replacing batteries.

Batteries are out of power
Just power cut
DC or AC connector of AC/DC transformer 
may not connect well

  Replace batteries
  Check the power supply
  Reconnect the connector

9

Trouble

shooting